Ask an Engineer
Model Comparison

GT11N1 vs GT11N2 vs GT11NM: Design Differences and Parts Interchangeability

The GT11N1, GT11N2 and GT11NM share a family name but not a parts book. What is physically different between the three 50 Hz ABB/Alstom machines, which components carry over, and how to write an RFQ that survives the drawing check.

The short answer: the GT11N2 is a different machine from the GT11N1, not an uprated one. Its compressor, pressure ratio, firing temperature and output all move up a step, and almost nothing in the hot gas path crosses over. The GT11NM is the opposite case — a modification package applied to an existing GT11N1 in the field, and the components it replaces define exactly which parts stop being interchangeable. For all three, the model designation on the data plate is not enough to quote from; you need the build standard behind it.

At a glance: three designations, three build standards

 GT11N1GT11N2GT11NM
Gross output, simple cycle~84 MW~109–115 MW~94 MW (N1 +10–12%)
IntroducedEarly 1990sMid 1990s2005, as a field uprate
Compressor14 stages, pressure ratio ~14:114 stages, pressure ratio ~15:1, higher mass flowN1 compressor; the 2008 NMC step added a compressor upgrade and a new rotor
Combustion systemSingle top-mounted silo combustorSingle silo: EV dry low-NOx, SB single burner, or syngasN1 silo, revised hardware
Turbine airfoil castingConventional (equiaxed)Conventional (equiaxed), moderate firing temperatureRevised blading, new vane carrier
Relationship to the N1BaselineNew frame size, not an uprateUprate kit on the N1

Why the model names mislead

ABB introduced the 84 MW GT11N1 in the early 1990s as a peaking and cogeneration machine, and the architecture is unusually explicit about maintenance: a single top-mounted silo combustor large enough for a crew to physically enter for inspection, a solid welded rotor forged in segments with no through-bolts, no centre bore and no separate wheels, axial exhaust that connects straight to an HRSG without a fabricated exhaust case, and compressor blading in high-chromium A-705 and A-565 alloys to resist corrosion. All of that carried into the GT11N2.

The N2 then scaled the thermodynamic cycle rather than the architecture: the same 14 compressor stages moved to roughly 15:1 pressure ratio with a higher mass flow, exhaust mass flow rose to around 399 kg/s, and output climbed to 109–115 MW depending on combustor option and frequency. Alstom's own positioning for the N2 was deliberately commercial — all turbine airfoils conventional cast, moderate firing temperature, longer parts life, lower parts cost. That is a design decision, not a weakness: it is precisely why N2 hot gas path hardware is the most price-sensitive in the family, and why independent manufacturing is economically viable there.

The GT11NM follows a completely different logic. Announced in 2005, it is an uprate of the installed N1 fleet, and it is defined by a narrow replacement scope: new turbine blades and vanes, new heat shield segments, a new vane carrier, and a new exhaust gas housing. Output rose by roughly 10–12% with no increase in fuel consumption, and CO emissions fell. In 2008 the NMC version extended the same programme with a compressor upgrade and a new rotor. Alstom reported the GT11N fleet past one million equivalent operating hours by the end of 2005 at 98.9% reliability and 96.0% availability across a six-year window — which is why so many of these units are still in dispatch today rather than retired.

Where the three actually differ

Compressor and cycle

The N2 is aerodynamically a larger machine. Higher mass flow at a higher pressure ratio means the compressor blading is not dimensionally or aerodynamically common with the N1, and the rotor stack, spacers and seals that position it differ accordingly. The NM keeps the N1 compressor as standard, which is the single most important fact for anyone holding N1 compressor stock: those parts remain valid on an NM unit, and stop being valid on an NMC unit.

Combustion system

All three use the single top-mounted silo combustor, and all three benefit from the same maintenance property — the chamber is physically accessible, so inspection does not require lifting the rotor. What differs is the burner and liner set. The N1 carries separate fuel-oil and gas nozzles, which is why it needs inter-connector cross-fire tubes and flow dividers to propagate flame between them; the later single-nozzle-per-fuel arrangement removed both items. A cross-fire tube is therefore an N1-generation part with no counterpart on a converted unit, and a GT11N1 parts list that includes one tells you the machine is still at the original two-nozzle build. The N2 offers three distinct combustor paths: EV dry low-NOx for natural gas at strict emission limits, SB single burner for power augmentation with water or steam injection, and a syngas variant that will run down to heating values near 2,000 kJ/kg. A burner quoted for one path will not serve another, and mixing them is the most common specification error we see on these units.

Hot gas path

The N1 and N2 both run conventional cast airfoils at moderate firing temperature, which is what delivers their long parts life. The NM raises the demand on the same gas path by extracting more work from it, and answers with revised blading and a new vane carrier — the hardware that sets vane position and cooling air distribution. This is where the interchangeability boundary sits, and it is not negotiable in service.

Rotor, casings and exhaust

The solid welded rotor principle is common to the family, which is exactly why rotor-adjacent parts are the easiest to confuse on a parts list. The NM's new exhaust gas housing is a visible tell: an uprated unit can often be identified from the exhaust end alone. For an operator with mixed fleet history, that is the fastest field check before ordering.

One nameplate, four builds: what the data plate does not tell you

“GT11N2” names a frame, not a configuration. Two units carrying the same designation can differ by more than 20 MW of gross output and by an entirely different combustor parts list, because the configuration is set on two independent axes: the compressor side (how many VIGV rows, and whether the NMC compressor upgrade was fitted) and the combustor side (EV dry low-NOx, SB single burner, or LBtu low-heating-value). Quoting from the model name alone is the most common reason a first article is rejected.

BuildGross outputEfficiencyHeat rateExhaustNOx, gas / #2 oil
EV, 60 Hz115.4 MW33.6%10,150 Btu/kWh399 kg/s at 531 °C25 / 42 ppm
EV, 50 Hz113.6 MW33.1%10,305 Btu/kWh399 kg/s at 531 °C25 / 42 ppm
SB, 60 Hz129.3 MW at fuel/water 1.8531.7%10,772 Btu/kWh415 kg/s at 522 °C25 / 65 ppm
Silo, 50 Hz (operating unit, Brestanica PB4/PB5)108.9 MW gas / 114.2 MW oil34.0% / 32.7%———
LBtu, low-Btu gasfuel LHV 2,000–4,000 kJ/kgup to 47% in combined cycle——single-digit demonstrated, full load
Read the table as ISO, gas-fired, at generator terminals. The SB column is a water- or steam-augmented rating at a fuel/water mass ratio of 1.85; Alstom's own positioning for the same path is “up to 140 MW of low specific cost peaking power” at a ratio up to 2.2, or 22 kg/s. It is the same machine running wetter, not a different build — so never set the 129.3 MW figure against a dry EV unit as if it were an alternative rating for the same duty. In combined cycle, 2×1 dual pressure without reheat, the frame reaches 348.4 MW at 51% net LHV efficiency on 60 Hz and 345.0 MW on 50 Hz.

Compressor side: 14 stages, shared with the GT24

Every GT11N2 build uses a 14-stage compressor at roughly 15:1 pressure ratio, quoted at 15.5:1 on the 60 Hz EV datasheet. It is the same family design Alstom used on the GT24 and validated on more than 95 machines before it entered the N2. Rows 1–7 carry 16% chromium blading with a precipitation-hardened surface treatment for corrosion resistance, and the optional inlet guide vane row delivers about 40% airflow turndown, which is what makes the fast start reliable. For procurement the practical point is narrow: compressor blading is the one group where no GT11N1 part crosses over, and where the VIGV row count alone changes the hardware list before any hot gas path item is discussed.

Turbine side: four stages, all IN738, all conventional cast

The turbine is four stages on a three-pressure cooling scheme, and every airfoil — blade and vane, all four rows — is INCONEL 738 in conventional equiaxed cast form. Alstom sold that as an economic argument rather than a performance one: longer parts life, lower parts cost, fully refurbishable, low fallout. It is also why independent manufacturing is commercially viable on this frame, and why a repair-and-recoat route frequently beats a new-part route on rows 2 to 4. Row 1 still carries the highest metal temperature and the coating life that governs the interval, so its remaining life — not its unit price — is the number the outage plan is built on.

Low-Btu is not a paper option

The LBtu combustor is a production configuration with reference plants, not a brochure variant. The first unit went to Baoshan Iron & Steel in Shanghai in 1994 for a 150 MW combined cycle plant. The largest reference is the 480 MW combined cycle at ThyssenKrupp's Santa Cruz steel mill in Rio de Janeiro, built around two GT11N2 low-Btu machines that start on natural gas and then run purely on blast furnace gas, compressed in two stages to about 16 bar — 200 MW to the mill, up to 280 MW exported. If an enquiry comes from a steel mill or a refinery, the fuel analysis matters more than the model name: combustor volume and the fuel nozzle set differ from the natural gas build, and the hot gas path sees a different firing profile.

Inspection access is designed in, not added on

The silo combustor is large enough for a crew to enter, and Alstom lists direct inspection of both the combustor internals and the first turbine stage as a design feature, backed by a defined set of borescope access points. In practice that shortens the diagnostic path before an outage: stage 1 hardware can be assessed without lifting the rotor, and the go/no-go on hot gas path scope is taken earlier, which is what actually protects the schedule. It also means the three questions we open every GT11N2 RFQ with — which build, which fuel, which frequency — can usually be answered from the site rather than from the drawing file.

Parts interchangeability: the practical matrix

Component groupN1 ↔ N2N1 ↔ NMWhat governs it
Turbine stage 1 bladesNoNoDifferent cooling geometry and coating build; NM blading is new hardware
Turbine stage 2–4 bladesNoNoMatched to the same cooling schedule as stage 1
Nozzle segments and vanesNoNoSet by the vane carrier and the firing temperature of the build
Heat shield segmentsNoNoReplaced as part of the NM scope
Vane carrierNoNoNew item in the NM kit; dictates vane fit
Exhaust gas housingNoNoNew item in the NM kit; also the field identifier
Compressor bladingNoYesNM retains the N1 compressor; NMC does not
Compressor rotor and spacersNoYesOnly the 2008 NMC step replaces the rotor
Combustor liner and burnersNoNoDepends on combustor path (EV / SB / syngas), not just model
Auxiliary skid and controlsNoPartlyGoverned by control system generation, not by frame
Read this as a procurement rule, not an engineering absolute. A part that physically fits is not a part that is released. Hot gas path hardware is matched to a specific cooling air schedule and coating build; substituting N1 blading into an NM position changes the metal temperature margin, and therefore the coating life model the outage interval was calculated on. When a drawing revision is not available, quote from the serial number and the upgrade history, not from the model name.

What an NM uprate does to your spare parts inventory

Because the NM kit replaced blades, vanes, heat shields, the vane carrier and the exhaust housing, an operator who has uprated an N1 is effectively running two parts populations across the unit's history. Legacy N1 hot gas path stock is not usable on the uprated machine, and holding it costs warehouse space and capital. The reverse error is more expensive: an operator still running an unmodified N1 should not accept NM-configuration hardware as an equivalent substitute, because the cooling and coating assumptions behind the outage interval no longer hold. Before any hot gas path order, confirm which of the three build standards the unit is actually at — N1, NM, or NMC.

Upgrade economics: kit, replacement, or run to the life limit

There is no universal answer, but the decision framework is narrow. An NM-style uprate is worth evaluating when the unit has remaining rotor and casing life, when the site needs incremental capacity without a new permit, and when the next hot gas path inspection is already due — because the kit work is absorbed into an outage that was going to happen anyway. Replacing the unit with a larger frame only makes sense when the balance of plant, the HRSG and the grid connection can absorb the additional output, which on a 1990s cogeneration site is rarely the case. Running to the life limit is defensible only where capacity payments do not justify the incremental megawatt.

What changes most between the three routes is not the capital number but the parts strategy behind it. An uprated unit needs a different spares population than the one the site has been stocking for fifteen years, and that transition is usually planned later than it should be.

How to specify an RFQ that survives the drawing check

Frequently asked questions

Is the GT11N2 an uprated GT11N1?

No. The GT11N2 is a larger machine on the same architectural principles: roughly 15:1 pressure ratio instead of about 14:1, higher mass flow and exhaust flow near 399 kg/s, and 109–115 MW instead of 84 MW. Its compressor blading, hot gas path hardware and rotor stack are not common with the GT11N1. The model that genuinely uprates the N1 is the GT11NM, delivered as a field modification from 2005.

What does the GT11NM upgrade actually replace?

The documented scope is turbine blades and vanes, heat shield segments, the vane carrier and the exhaust gas housing. Output increases by roughly 10–12% without additional fuel, and CO emissions fall. A later NMC version added a compressor upgrade and a new rotor, which is a further divergence and should be confirmed separately before any hot gas path order.

Can I fit GT11N1 blades into a GT11NM unit?

No. NM blading is new hardware matched to a revised vane carrier and cooling air distribution. Fitting N1 blading changes the metal temperature margin and invalidates the coating life model behind the outage interval. The same restriction applies to nozzle segments and heat shields.

Which parts do carry over from GT11N1 to GT11NM?

Compressor blading, compressor rotor and spacers, plus most of the auxiliary skid, because the NM package retains the N1 compressor. Note the boundary: the 2008 NMC step replaces the compressor and rotor, so N1 compressor stock is valid on an NM unit but not on an NMC unit.

How do I identify which build standard a unit is at?

Start at the exhaust end: a new exhaust gas housing is the visible tell of an NM uprate. Then confirm against the data plate serial number and the site's upgrade records. Where records are incomplete, a drawing number with its revision letter, or a dimensional check on the vane carrier, resolves it before any order is placed.

Where can GT11N1, GT11N2 and GT11NM spare parts be manufactured?

ZURN Power manufactures hot gas path blading, combustion hardware, compressor blading and rotor components for all three build standards to OEM drawing or from a supplied sample, with EN 10204 3.1 certification. Typical lead time is 8–14 weeks for hot gas path castings and 4–8 weeks for machined compressor components. Send the drawing number and upgrade history for a manufacturability assessment.

Why can two GT11N2 units have different output?

Because the designation covers four builds. On the combustor side, an EV dry low-NOx machine is rated 115.4 MW at 60 Hz and 113.6 MW at 50 Hz, an SB single-burner machine reaches 129.3 MW when run at a fuel/water ratio of 1.85, and production LBtu units in the field publish around 108.9 MW on gas. On the compressor side, VIGV row count and the NMC compressor upgrade change both mass flow and the parts list. Always quote frequency, combustor type and fuel before discussing price.

Does the GT11N1 use cross-fire tubes?

Yes. The GT11N1 has separate fuel-oil and gas nozzles, which is exactly why it needs inter-connector cross-fire tubes and flow dividers. The later single-nozzle-per-fuel arrangement eliminated both, so on a converted machine there is no cross-fire tube to replace. If a spare parts list for a “GT11N1” includes cross-fire tubes, the unit is at the original two-nozzle build — a useful field identifier when site records are incomplete.

Need a GT11N1, GT11N2 or GT11NM Part Quoted?

Send the data plate photograph, drawing number and upgrade history. Our engineering team will confirm the build standard against the drawing before quoting, so the first article is the right article.

Request a QuoteDownload Parts Catalog
China & Asia-Pacific[email protected]+86 186 1687 9105
General Inquiries[email protected]Global — All Markets
💬 WhatsApp · +86 186 1687 9105✉ Email · [email protected]📞 Call · +86 186 1687 9105